Development of autonomous monitoring and performance evaluation system of grid-tied photovoltaic station

This work aims to improve the existing monitoring systems MS for two grid-connected PV stations GCPVS of URERMS ADRAR, to eliminate its limitations. This improvement consists of developing an MS which is used for two PV stations with different configurations. This MS contains new LabVIEW-based monitoring software for visualizing real-time measured data and evaluating GCPVS performance. In addition, it illustrates the 2D and 3D real-time relationships of PV system parameters, which allow us to understand the dynamic behavior of PV system components. This developed monitoring software synchronizes also the various data acquisition units DAU of GCPVS, allowing simultaneous data access.To perform a reliable performance analysis and a comparative study of different GCPVS based on accurate measurements, the sensor's calibration is performed with its DAU. The MS autonomy is ensured by integrating developed PV-UPS. A graphical user interface is provided for the evaluation of PV-UPS performance.     

气藏型储气库注气期试井分析探讨

针对气藏型储气库注采井注采过程中储层物性参数影响因素不明确、注采能力不对称的问题。基于相国寺储气库井下连续油管试井测试结果,提出储气库注气期“温降效应”、“变表皮效应”的概念,分析了储气库注采过程中温降效应、变表皮效应以及储层应力敏感对注采的影响。通过气藏型储气库注气期试井分析技术,研究各因素在试井曲线上的响应特征以及对试井解释参数的影响。结果表明:①相对于采气期试井测试,注气期测试得到的储层物性参数具有同样的参考价值;②储气库温降效应对于试井解释结果的影响可忽略不计,而在不同注采运行周期内,变表皮效应以及应力敏感效应影响差异较大;③编制储气库注采运行方案时应充分考虑变表皮效应与应力敏感的影响,在不同注采运行周期内开展试井测试获取准确的储层参数值。研究成果为储气库试井测试与解释提供了重要的研究依据和理论指导。     

Improved energy storage density and energy efficiency of Samarium modified PMNT electroceramic

We report the improved energy storage density and efficiency after 2.5% of Samarium substitution in ferroelectric Pb[(Mg_1/3Nb_2/3)_0.80Ti_0.20]O₃ (PMNT) electroceramic. The microstructure and surface morphology were analyzed and correlated with various functional properties. The energy storage density, leakage current density, ferroelectric and dielectric properties were investigated thoroughly, indicating that Samarium's substitution significantly modified the microstructure, the dielectric strength, breakdown electric field, and turned ferroelectric PMNT to relaxor ferroelectrics. Due to the relaxor nature, the gap between remanent polarization and maximum polarization increases with the substitution of Samarium in PMNT matrix, which further increases the recoverable energy storage density and energy efficiency. A nearly 100% increase in recoverable energy density and efficiency was obtained at an electric field strength of 35 kV/cm at room temperature (～296 K). The electroceramic shows maximum energy density near the ferroelectric phase transition temperature (325 K–345 K) region and provides a moderate energy storage density for possible applications in power microelectronics.     

Hydrogen wettability of clays: Implications for underground hydrogen storage

This study investigates the ability of hydrogen (H₂) to wet clay surfaces in the presence of brine, with implications for underground hydrogen storage in clay-containing reservoirs. Rather than measuring contact angles directly with hydrogen gas, a suite of other gases (carbon dioxide (CO₂), argon (Ar), nitrogen (N₂), and helium (He)) were employed in the gas-brine-clay system under storage conditions (moderate temperature (333 K) and high pressures (5, 10, 15, and 20 MPa)), characteristic of a subsurface environment with a shallow geothermal gradient. By virtue of analogies to H₂ and empirical correlations, wettabilities of hydrogen on three clay surfaces were mathematically derived and interpreted. The three clays were kaolinite, illite, and montmorillonite and represent 1:1, 2:1 non-expansive, and 2:1 expansive clay groups, respectively. All clays showed water-wetting behaviour with contact angles below 40° under all experimental set-ups. It follows that the presence of clays in the reservoir (or caprock) is conducive to capillary and/or residual trapping of the gas. Another positive inference is that any tested gas, particularly nitrogen, is suitable as cushion gas to maintain formation pressure during hydrogen storage because they all turned out to be more gas-wetting than hydrogen on the clay surfaces; this allows easier displacement and/or retrieval of hydrogen during injection/production. One downside of the predominant water wettability of the clays is the upstaged role of biogeochemical reactions at the wetted brine-clay/silicate interface and their potential to affect porosity and permeability. Water-wetting decreased from kaolinite as most water-wetting clay over illite to montmorillonite as most hydrogen-wetting clay. Their wetting behaviour is consistent with molecular dynamic modelling that establishes that the accessible basal plane of kaolinite's octahedral sheet is highly hydrophilic and enables strong hydrogen bonds whereas the same octahedral sheet in illite and montmorillonite is not accessible to the brine, rendering these clays less water-wetting.     

Sn substitution endows NaTi2(PO4)3/C with remarkable sodium storage performances

The further development of clean energy requires the use of more stable and reliable energy storage system. In addition to lithium ion battery power supplies, sodium ion batteries also have prospects for application and development thanks to the low cost and abundant resource. NaTi₂(PO₄)₃ has attracted much attention due to its three-dimensional channels for sodium ion transfer. In order to meliorate sodium storage properties of NaTi₂(PO₄)₃ electrode, a facile strategy of Sn substitution at Ti sites was employed, and a series of electrodes were successfully synthesized through sol-gel route. The electrochemical performances of Sn substituted composites are significantly improved compared with bare NaTi₂(PO₄)₃/C. And it was found that NaSn_0.2Ti_1.8(PO₄)₃ (NTP/C-Sn-2) delivers the largest capacity, and it also demonstrates the outstanding cycling performances. NTP/C-Sn-2 has discharge capacity of 131.1 mAh g⁻¹ at 4 A g⁻¹ in rate test and 121.4 mAh g⁻¹ at 1 A g⁻¹ after 1000 cycles in cycling test. The experimental results show that NaTi₂(PO₄)₃/C with Sn substitution with proper content exhibits the great potential in anode for sodium ion batteries, and can further provide reference for next generation electrode materials and battery systems.     

Development of New Product: Rambutan Pulpy Juice

This study aimed to know the effect of adding pulp in rambutan fruit juice on the characteristics of rambutan juice during storage. Research using the CRD, the treatment were kind of pulp (mandarin and rambutan) and pulp concentration (5%, 7.5%, and 10%). The results showed that the addition of pulp significantly affect the characteristics of rambutan juice (pH, vitamin C, total acid) during storage. Pulpy juice with the most prefered was addition of rambutan pulp as much as 7.5% (w/v) and the addition of citrus pulp as much as 7.5% (w/v) with the score of 3-4 (moderate like - like).     

Extended preservation of raw beef and pork meat by hyperbaric storage at room temperature

Hyperbaric storage (HS) was evaluated as a new food preservation methodology at room temperature (RT) for beef and pork meat, both minced and in pieces, and compared to refrigeration (RF) storage. The meat samples were stored at 50, 75 and 100 MPa and variable RT up to 60 days. HS at 75 and 100 MPa could not only inhibit microbial growth but also inactivate microorganisms. Regarding physicochemical analyses, an overall equal to better pH maintenance in HS samples was achieved, and similar colour differences between HS and RF were observed. Generally, similarities in moisture content and drip loss between HS (mostly 75 and 100 MPa) and RF were detected (tendency for lower values in the former and higher values in the latter for the higher pressure level). Protein solubility revealed a decrease of sarcoplasmic protein values during storage with a pressure level dependency in some samples.     

Effect of stoichiometry and Cu-substitution on the phase structure and hydrogen storage properties of Ml-Mg-Ni-based alloys

To improve the electrochemical properties of rare-earth–Mg–Ni-based hydrogen storage alloys, the effects of stoichiometry and Cu-substitution on the phase structure and thermodynamic properties of the ...     

Structure,dielectric properties of novel Ba(Zr,Ti)O3 based ceramics for energy storage application

(1-x) Ba(Zr_0.2Ti_0.8)O₃-x Na_0.5Bi_0.5TiO₃ (x = 0, 10, 20 30, 40, 50 mol%) (BZTN) ceramics are prepared by the traditional solid phase method. All BZTN ceramics exhibit a pseudo-cubic BZT based perovskite structure. Both the average grain size and the relaxor ferroelectricity of BZTN ceramics gradually increase with increasing NBT content. The W_rec of 3.22 J/cm³ and η of 91.2% is obtained for the BZTN40 ceramic at 241 kV/cm. BZTN40 ceramic also exhibits good temperature stability from room temperature to 150 °C and frequency stability from 1 Hz to 100 Hz. A P_D of 0.621 J/cm³ and a t_0.9 of 82 ns is obtained for the BZTN40 ceramic at 120 kV/cm. BZTN ceramics show application potential in energy storage and pulse power capacitors.     

Changes in the physical properties of honey powder during storage

Honey powders produced by spray drying with the addition of Arabic gum and sodium caseinate were characterised in terms of the influence of storage time on the following physical properties: particle size, moisture content, water activity, bulk density, flowability and hygroscopicity. The storage affected those properties; after 12 weeks of storage, particle size decreased (except Arabic gum powder treated as a control sample), moisture content and water activity increased, hygroscopicity decreased. Changes in bulk density, particle size and moisture content caused the rise of Hausner ratio value; however, the powders were still characterised by a very good flow properties and low cohesiveness. The colour of reconstituted powders was also affected by storage; in most of samples, the darkening, reduction in redness and yellowness were observed. Colour parameters were the most stable in powders obtained with the addition of 2% w/w of sodium caseinate.